Types of Cement in South Africa and Their Uses: Grey, White & Masonry
Quick answer: A bag code such as CEM II/B-L 32,5 N gives the cement type, the extender, the strength class and the early-strength speed. Grey 32,5 or 42,5 cement covers mortar, plaster and ordinary home concrete. Tile adhesive and grout are cement-based products with their own standards, not types of cement. Before you buy, look for “NRCS Approval” and a licence number on the bag.
The code on a South African cement bag gives the cement’s type, its extender and its strength class. This guide decodes that code, then goes through each cement you are likely to meet: grey general-purpose cement, limestone cement, white cement, rapid-hardening cement and masonry cement. It also sorts out the products people confuse with cement, including lime, mortar, tile adhesive, grout and plaster of Paris. Each section answers the questions people ask about that product, so go straight to the one you need. When you know what to buy, the Concrete Calculator, Mortar Calculator and Plaster Calculator turn it into a bag count.
In this article
- How to read a cement bag
- The main cement types, CEM I to CEM VI
- What 32,5, 42,5, 52,5, N and R mean
- Which grey cement for which job
- Limestone cement, and how lime differs
- White cement
- Rapid-hardening and high-strength cement
- Masonry cement
- Products people mistake for cement
- How to check a bag is approved
- Sources
- Frequently asked questions
How to read a cement bag
Every bag of cement sold in South Africa is marked with a designation that follows the same pattern on every brand. The pattern comes from SANS 50197-1, the South African version of the European cement standard EN 197-1; the SABS store lists the 2013 edition. Take CEM II/B-L 32,5 N, a code you will find on PPC cement, and read it from left to right.
| Part of the code | Example | What it tells you |
|---|---|---|
| Main type | CEM II | Portland-composite cement: cement clinker plus an extender. CEM I is plain Portland cement. CEM III, IV, V and VI carry larger shares of slag, fly ash or both. |
| Extender share | /B | A is the smaller share of extender, 6 to 20%. B is the larger share, 21 to 35%. |
| Extender material | L | What the extender is: L is limestone, V is fly ash, S is slag and M means a mix of two or more, written in brackets such as (S-V). |
| Strength class | 32,5 | The minimum strength at 28 days, in megapascals (MPa). The classes are 32,5, 42,5 and 52,5. |
| Early strength | N | N is normal early strength. R is rapid early strength. |
South African data sheets use a decimal comma, so you will see 32,5 N as often as 32.5N. The spacing varies by manufacturer, but the meaning does not.
A brand name is not a cement type. The same brand can be a different type depending on which factory filled the bag. PPC SureCem 32,5 N is CEM II/B-L at five plants, CEM V/A (S-V) at Meyerton and CEM IV/B (V) at Highveld. AfriSam All Purpose is 42,5 N whether the bag holds CEM V/A (S-V) or CEM II/B-M (L). Buy on the strength class, and use the type to see what is in the bag.
The main cement types, CEM I to CEM VI
SANS 50197-1 names five main types of common cement, and the newer SANS 50197-5 adds a sixth. They differ in how much cement clinker they hold and what replaces the rest. Not every combination the standard allows is made in South Africa, and the table shows what the manufacturer data sheets list.
| Type | Name | What is in it | Seen on SA bags |
|---|---|---|---|
| CEM I | Portland cement | 95 to 100% clinker | AfriSam Rapid Hard and Afrimat Fastcast (52,5 R), Sephaku 52 (52,5 N) |
| CEM II | Portland-composite, and slag, fly ash or limestone cements | 50 to 94% clinker with 6 to 50% of one extender or a mix, depending on the grade | PPC SureBuild and SureCem, Sephaku 42,5 N, AfriSam All Purpose, abe CEM-blanc |
| CEM III | Blastfurnace cement | Mostly slag: 36 to 95% | None on the retail data sheets read for this guide |
| CEM IV | Pozzolanic cement | 45 to 89% clinker with 11 to 55% fly ash or similar | PPC SureBuild at some factories, Afrimat BuildCrete |
| CEM V | Composite cement | 20 to 64% clinker with slag and fly ash together | PPC SureCem and SureBuild at some factories, AfriSam All Purpose and StarBuild |
| CEM VI | Composite cement (SANS 50197-5) | 35 to 49% clinker, 31 to 59% slag and 6 to 20% of a second extender | Afrimat BuildCrete (S-V) at two plants |
The standard keeps the extender in the mix on purpose. Extenders cost less than cement clinker, and the Concrete Society of Southern Africa’s 2024 technical leaflet on cementitious materials says extenders are generally cheaper than Portland cement and can improve the impermeability and durability of hardened concrete. The trade-off is early strength: as the extender content of a cement increases, early-age strength gain is generally slower.
What 32,5, 42,5, 52,5, N and R mean
The class number is the minimum strength, in MPa, that a standard test mortar reaches at 28 days. A 32,5 cement must test at least 32,5 MPa and under 52,5 MPa. A 42,5 cement must test between 42,5 and 62,5 MPa. A 52,5 cement must test 52,5 MPa or more. These are laboratory test-mortar strengths, not the strength of your concrete.
The letter is about speed. The standard sets an early-age hurdle: a 2-day or 7-day minimum the cement has to clear before the 28-day figure counts.
| Class | N: normal early strength | R: rapid early strength | Strength at 28 days | Initial setting time |
|---|---|---|---|---|
| 32,5 | 16,0 MPa at 7 days | 10,0 MPa at 2 days | 32,5 to under 52,5 MPa | At least 75 minutes |
| 42,5 | 10,0 MPa at 2 days | 20,0 MPa at 2 days | 42,5 to under 62,5 MPa | At least 60 minutes |
| 52,5 | 20,0 MPa at 2 days | 30,0 MPa at 2 days | 52,5 MPa or more | At least 45 minutes |
Real bags can beat the minimum: PPC’s SureBuild data sheet gives a typical 28-day strength of over 45 MPa against a 42,5 minimum. Use the minimum when you plan, and the manufacturer’s data sheet when you need the real figure.
Which grey cement for which job
For most home building the answer is more relaxed than the shelf makes it look. The 2024 technical leaflet says any SANS 50197-1 common cement of class 32,5 N or higher should suit conventional structural concrete in a non-aggressive environment, and that the choice is normally made on economy. The class matters more in the cases below.
| Job | What to use | Why |
|---|---|---|
| Brick and block mortar, plaster | 32,5 N, 32,5 R or 42,5 N, or masonry cement | PPC SureCem (32,5 N), Sephaku 32 and Afrimat DuraBuild Plus (32,5 R) and the 42,5 N cements are all listed for mortar and plaster by their makers. |
| Foundations, paths, driveways, slabs and columns | 32,5 R or 42,5 N from the manufacturers’ lists; follow the class on your plans | Sephaku lists 10 to 15 MPa for foundations, 20 to 25 MPa for paths and driveways and 25 to 30 MPa for slabs and columns, on both its 32,5 R and 42,5 N sheets. |
| High-strength concrete, floors and roads with sawn joints | 42,5 N or higher | The 2024 leaflet sets 42,5 N as the lowest class here, with no more than 30% extender for sawn joints. |
| Precast that must be handled early without steam curing | 42,5 R or higher, low extender | The leaflet says high early strength is reached most economically with 42,5 R and higher; cements with more extender suit steam curing. |
| Precast bricks, blocks and pavers | Choose on cost | The leaflet says that if elements can be handled the day after casting, economy decides. |
Brands sit on the shelf by class. The 42,5 N shelf holds PPC SureBuild, AfriSam All Purpose, Sephaku 42,5 N and Afrimat BuildCrete. The 32,5 shelf holds PPC SureCem, AfriSam StarBuild, Sephaku 32 (a 32,5 R) and Afrimat DuraBuild Plus (also 32,5 R). PPC SureRoad and Sephaku SepROAD are 32,5 N cements made for road work, and PPC says SureRoad is not for general building.
Whatever you choose, use the class your plans or engineer specify. A lower class cannot be swapped in where a higher strength is required.
Know the class? Turn your slab or footing size into a bag count.
Use the Concrete Calculator →Limestone cement, and how lime differs
What limestone cement is
Limestone cement is common cement in which finely ground limestone replaces part of the clinker. It carries the letter L in its code: CEM II/A-L holds 6 to 20% limestone and CEM II/B-L holds 21 to 35%. The standard allows L when the limestone’s organic content is no more than 0,50%, and LL when it is no more than 0,20%.
You are probably already using it. PPC SureCem is CEM II/B-L at five plants, Sephaku’s SepROAD 32,5 N is CEM II/B-L, and Afrimat DuraBuild Plus is CEM II/B-L at Lichtenburg. The data sheets show the same strength classes as any other cement of that class, because the standard sets the same limits.
Limestone is not lime
The limestone in cement is calcium carbonate. Building lime is hydrated lime, a different material, and the 2024 technical leaflet notes that no calcium hydroxide or quicklime is used in cement made to SANS 50197-1. The two also do different jobs. Cement is the binder that hardens with water. South African building lime is non-hydraulic, so on its own it does not harden that way.
In mortar and plaster, lime is an optional addition that improves workability and water retention. Use building lime of type A2P or A3P to SANS 523, and never quicklime, lime wash or agricultural lime. The Concrete Society’s mortar leaflet sets a maximum of 10 kg lime per 50 kg cement in Class I mortar and 25 kg in Class II. Lime is not used with masonry cement.
White cement
White cement is Portland cement made from raw materials with almost no iron, which is what keeps it white. It is graded like grey cement, by type and strength class. The South African example read for this guide is abe CEM-blanc, which abe describes as general-purpose white Portland cement, CEM II/B-L 42,5 N to SANS 50197-1, in 25 kg bags.
Do you get white cement in South Africa?
Yes. Specialist suppliers such as abe and Iox Africa list white Portland cement, Iox in CEM I and CEM II, in bulk and in 25 kg bags. Cemcrete’s own page says it no longer sells its white cement directly, so do not rely on one source. Ask a supplier for the type, the class and the NRCS approval number before you pay, as you would with grey cement.
Some retail packs sold as white cement name no standard on the product page. If the label names neither, ask the supplier what is in the pack before you use it for anything structural or watertight.
White cement vs grey cement
The difference is colour, and where that colour matters. Grey cement does the structural work. White cement goes where the finish shows, and abe lists coloured mortars, pool plaster, pavers, grouts, adhesives and exposed aggregate among its uses. Both follow the same classes, so a white cement of class 42,5 N is sold against the same strength limits as a grey 42,5 N.
Price depends on pack size and supplier, so ask for a quote per bag rather than trusting one figure from a search.
White cement vs plaster of Paris
They are different materials. White cement is a hydraulic binder that hardens with water, like grey cement. Plaster of Paris is a gypsum-based plaster that dries quickly, and Powafix, for one, describes its plaster of Paris that way. Both are white powders mixed with water, which is where the mix-up starts. Plaster of Paris is not a substitute for cement anywhere that gets wet or carries load.
Rapid-hardening and high-strength cement
Rapid-hardening cement is cement with an R after the class. The fastest is 52,5 R, which must reach 30 MPa at 2 days. AfriSam Rapid Hard is CEM I 52,5 R, and AfriSam lists early stripping, precast and bridge launching among its uses. Afrimat’s October 2024 safety data sheet lists Fastcast and Rapidcem as CEM I 52,5 R and also as CEM II/A-V 52,5 N, so the bag marking decides which you hold. Sephaku 52 is CEM I 52,5 N. PPC SureCast is 42,5 R.
These are specialist cements for precast, early stripping and cold-weather work, where waiting for strength costs money. AfriSam describes Rapid Hard as a pure cement with a higher carbon footprint than its blended cements, which is part of why general building uses 32,5 and 42,5 instead. If you only need to strip shuttering a day earlier, ask your supplier whether a 42,5 R meets the job before you move to 52,5 R.
Masonry cement
Masonry cement is made to a different standard, SANS 50413-1, and it is for mortar and plaster only. PPC SureWall is the example: MC 22,5 X, where MC is masonry cement, 22,5 is the strength class in MPa and X means no air-entraining agent. PPC says it improves workability and water retention in mortar and plaster, and that it must not be used for concrete.
The NRCS notice requires a masonry cement bag to say it is for the preparation of mortar and plaster only. Do not add lime to a masonry cement mix, and do not substitute it for common cement in a slab, a footing or a bedding mix you were told to make with 32,5 or 42,5.
Products people mistake for cement
Cement vs mortar vs concrete vs screed
Cement is the binder. The rest are mixes made with it. SANS 10400-K defines mortar as a mixture of cementitious materials, sand and water, and its walling rules assume Class II mortar. Concrete adds stone to cement, sand and water. A screed is cement and fine aggregate laid on a base, and AfriSam’s floor-finish guide gives 50 kg of cement to 130 litres of moist, loose sand. The Screed Calculator, Mortar Calculator and Brick Calculator turn those mixes into bags and bricks.
Tile adhesive and grout
Tile adhesive and tile grout are cement-based products with polymers and fillers added, and they follow their own classification, not the cement standard. TAL, for example, classes its adhesives and grouts to SANS 52004 and EN 12004: C1T and C2TS1 for adhesives, CG1 and CG2W for cementitious grouts. Epoxy grouts are a separate class. “Tile cement” is a shop phrase for cement-based tile adhesive, not a type of cement. Pick tile adhesive and grout by the tile and the room, and size the job with the Tile Calculator.
Is grout the same as cement?
No. The cement in a cementitious grout is one ingredient, and the product is built for narrow tile joints, not for bedding or structure. Never use plain cement slurry in place of grout on a tiled floor you want to last.
How to check a bag is approved
Cement sold in South Africa falls under the NRCS compulsory specification for cement, VC 9085. The amendment gazetted as Notice 2570 of 2024 took effect about a year after it was gazetted on 14 June 2024. It says common cement must meet the latest edition of SANS 50197-1 and masonry cement the latest edition of SANS 50413-1, and it sets out what the packaging must show.
What the bag should carry
- The words “NRCS Approval” followed by the licence (LOA) number.
- The SANS standard it was made to, and the strength designation, such as CEM II/B-L 32,5 N.
- The manufacturer, trade name or trademark, the importer if different and the factory.
- A date or code that traces the bag to the day of packing.
- The manufacturer’s guidelines for using that cement.
- The mass, and for masonry cement the statement that it is for mortar and plaster only.
An NRCS licence is issued for each cement type from each source, so the number tells the regulator exactly which product you hold. Licences issued under the 2007 specification expire five years after the 2024 notice was published. Contact details for the NRCS are on nrcs.org.za if you want a number confirmed.
The checks exist because weak cement does reach shelves. The NRCS recalled Econo Cement CEM V/A (S-V) 32,5 N nationwide in December 2023 after sampling showed it failed the minimum strength. A TimesLIVE report on 12 September 2026 quoted the NRCS saying that some products have failed the minimum strength requirements. Buy from a supplier who can show you the bag marking, keep the packaging details of anything structural, and if a bag has no approval number, leave it on the shelf.
Sources
The figures in this guide come from the documents below, all read in November 2026. Standards were read through the manufacturer data sheets and technical leaflets that cite them, not from the standards themselves, and the SABS store lists SANS 50197-1:2013 without stating whether a newer edition exists.
- Government Notice 2570 of 2024 (Gazette 50826): amendment of VC 9085, the compulsory specification for cement
- PPC SureCem 32,5 N data sheet (2026) and PPC SureBuild data sheet
- AfriSam 2026 cement comparison chart
- Afrimat BuildCrete data sheet
- Sephaku Cement product range
- abe CEM-blanc white cement
- TimesLIVE, SA losing war on substandard cement (12 September 2026)
- SABC News, NRCS recalls Econo Cement (11 December 2023)
- Concrete Society of Southern Africa, Cementitious materials for concrete: standards, selection and properties (technical leaflet, 2024), which tabulates SANS 50197-1 and gives the cement selection guidance quoted above.
- Concrete Society of Southern Africa, Mortar mixes for masonry (2024), for the building lime limits.
- Manufacturer and supplier pages for the products named: PPC (SureCem, SureBuild, SureCast, SureWall, SureRoad), Sephaku, Afrimat (data sheets and the October 2024 safety data sheet), AfriSam (guides and chart), Iox Africa, Cemcrete, Powafix and TAL.
- SANS 10400-K:2011 for the mortar definition.
Plastering a wall or laying tiles once you have the cement sorted?
Read our Plastering & Painting Cost Guide →Frequently asked questions
South African cement follows SANS 50197-1, which names five main types: CEM I (Portland cement), CEM II (Portland-composite), CEM III (blastfurnace), CEM IV (pozzolanic) and CEM V (composite). The manufacturer sheets read for this guide show CEM II, IV and V on retail bags, sold in strength classes 32,5, 42,5 and 52,5, with N for normal or R for rapid early strength. Masonry cement and white cement are sold alongside them, and lime, tile adhesive and grout are different products.
The number is the minimum strength in megapascals that the cement reaches at 28 days: 32,5 MPa for the lower class and 42,5 MPa for the higher one. Manufacturers list both for mortar, plaster, block making and ordinary home concrete. Use the class your plans or engineer specify, because a lower class cannot be swapped in where a higher strength is required.
No single cement wins. Any grey 32,5 N, 32,5 R or 42,5 N cement suits plaster when the mix is right, and manufacturers list SureCem, Sephaku 32, DuraBuild Plus, SureBuild, All Purpose, Sephaku 42,5 N and BuildCrete for it. Masonry cement, marked for mortar and plaster only, is the other option, and the plaster calculator gives you the bags and sand for your wall area.
Yes, through specialist suppliers. abe lists CEM-blanc in 25 kg bags and Iox Africa lists white CEM I and CEM II, while Cemcrete says its own white cement is no longer sold directly. Ask for the class and the NRCS approval number before you buy, because small retail packs sold as white cement do not always name a standard.
Colour. White cement is made from raw materials with almost no iron, and it is graded exactly like grey cement, by type and strength class, so a white 42,5 N has the same strength limits as a grey 42,5 N. It goes where the finish shows, such as pool plaster and pavers, and grey cement does the structural work.
No. White cement is a hydraulic binder that hardens with water like grey cement. Plaster of Paris is a gypsum-based quick-drying plaster. Both are white powders mixed with water, which is where the confusion starts, but they are different materials, and plaster of Paris is not a substitute for cement in anything that gets wet or carries load.
If a bag says CEM II/A-L or CEM II/B-L, it is limestone cement: ground limestone replaces 6 to 20% (A) or 21 to 35% (B) of the clinker. You are probably using it already, because PPC SureCem is made that way at five plants. It must still clear the same strength limits as any other cement of its class.
Cement is the binder that makes mortar and concrete harden. South African building lime is non-hydraulic, so it does not harden by itself the way cement does. It is an optional addition that makes mortar and plaster more workable and better at holding water. Use building lime of type A2P or A3P to SANS 523, and never with masonry cement.
No. Tile grout and tile adhesive are cement-based products with added polymers and fillers, classified by their own standard (TAL, for example, classes its products to SANS 52004 and EN 12004, such as C1T adhesives and CG2W grouts). Epoxy grout is a separate class. Tile cement is a shop phrase for cement-based tile adhesive, not a type of cement.
Read the bag. Under the NRCS compulsory specification for cement, VC 9085, the packaging must carry NRCS Approval followed by the licence number, the standard it was made to, the strength designation, the manufacturer, the factory and a date or code for the day of packing.